SEN P-8000 Submersible Pond Pump

  • Vortex Impeller
  • Multi-use
  • Powerful, Quiet, Reliable
  • Thermally protected
  • Special ceramic shaft
  • Silent operation
  • Practical Handle
  • Maintenance free
  • High Performance
  • Ideal for Pond & Freshwater.
  • Trouble Free
  • Cord Length 20 feet

P-8000 Pump Vortex Impeller

Application

  • Outdoor Falls (8000 gallon)
  • Pond
  • Hydroponics
  • Fountains
  • Aquarium
  • Water movement
Max. Flow (GPH) 8000 GPH
Power (watt) 640 watt
Max. Head (feet) 30 feet
Volt 115V/60Hz
Cord Length 20 feet
Size (LxHxW) 15 3/4"x 9 3/4"x 8 3/4"
Inlet 2"
Outlet 1.5"
Weight 27#

SEN P-2600 Submersible Pond Pump

  • Vortex Impeller
  • Multi-use
  • Powerful, Quiet, Reliable
  • Thermally protected
  • Special ceramic shaft
  • Silent operation
  • Practical Handle
  • Maintenance free
  • High Performance
  • Ideal for Pond & Freshwater.
  • Trouble Free
  • Cord Length 20 feet

P-2600 Pump Vortex Impeller

Application

  • Outdoor Falls (2600 gallon)
  • Pond
  • Hydroponics
  • Fountains
  • Aquarium
  • Water movement
Model P-2600 Pond Pump
Volts 115 V / 60 
Power (watts) 225 watt
Max. Head 14 feet
Max. Flow (GPH) 2600 GPH
Cord Length 20 Feet
Size (LxHxW) 10 1/2"x 6 1/2" x 5 3/4"
Inlet 1.5"
Outlet  1"
Weight 7#

Application

Please do fully immerge the pump into the pond and fix it well on horizontal level.  

       

Safety Instruction

  1. Make sure that your electrical voltage is the same voltage as mentioned on the label of the pump.
  2. To avoid the possibility of the plug and the receptacle to get wet, creating a drip loop will help prevent water travel along the cord to the receptacle and plug.
  3. Use pump with water only.  Do not use Gasoline or Solvent that is flammable or explosive fluids.
  4. Do not run pump without water.  Even if the pump is running continuously, permanent damages could occur.
  5. Do not operate pump if it is damaged or malfunctioned cord or plug.
  6. Do not operate pump if it is dropped or damaged in any matter.
  7. Always unplug the pump from the outlet when not in use before putting on or taking off parts and before cleaning.  Never yank the cord to pull it from the outlet.  Grasp the plug and pull to disconnect.
  8. Securely install the pump before operating.
  9. Do not expose the appliance to weather of temperatures below freezing.
  10. Only use a proper rating extension cord when needed.  a cord rated for less amperes of watts than the pump rating may overheat. *** Arrange cords so they will not be tripped or pulled out of socket accidentally.
  11. Do not attempt to repair pump yourself.  Return the pump to the authorize service center for service or discarding of the pump.
  12. Always us a properly grounded receptacle.

Maintenance (Impeller)

  1. Disconnect the plug before performing maintenance.
  2. Gently take off the impeller housing form the pump motor unit
  3. Pull out the complete magnetic impeller set from the motor unit
  4. Clean and wipe complete magnetic impeller set to remove accumulated dirt, debris and deposits.  Only rinse with running water. *** Do not use sop or cleaning agents.  Do not take the impeller apart.  It is not designed to be taken apart.  If the magnetic impeller set does not work properly, the complete magnetic impeller set will be replaced.
  5. Re-install the complete impeller set onto shaft, impeller housing

SEN P-2600 & SEN P-8000 Submersible Pond Pump Parts

1 Water Inlet Cover
2 Portable Cover
3 Sole Plate
4 Impeller
5 Rotor Starter Cover
6 Water outlet sealed cover
7 Long water outlet connector
8 Long water outlet connector fixture
9 Short water outlet connector
10 Screws, 6 pieces

 


Home |  About Us |  Contact |  Dr. Aqua  |  Pond ProductsOn-line Store Front   |  koi Land


1998 Won Brothers, Inc.  All rights reserved