• Controlled by micro computer with high precision of ±1°F

• UNBREAKABLE TITANIUM TUBE

• The indicating controller has "heat on" and "power on" indicator lights.

• Titanium heating tube offers a excellent chemical resistance in saltwater and freshwater.

• Controller provide a digital temperature LCD display that indicates actual temperature of the water  

• Heater power cord length is 6 ft. (72") long heavy duty cable and it permits easy installation.

• Automatic protection device activates when sensor wiring is disconnected or shorted. 

• Double heating tube

• Very durable & reliable

• Safe & easy temperature control

• Aquarium IC thermostat uses IC to control the heater to adjust desired aquarium temperature

• The heating tube unit is a submersible completely for SALTWATER or FRESHWATER aquarium.

• The heating tube unit can be mounted either vertically or horizontally.

• Operating temperature range: 68º  F to 93º F

• Heavy duty heat and shock resistance

• A temperature re-settable element that install in the control unit will activate shut off automatically for safety if temperature reaches at the indicated temperature. 

• Ideal for SALTWATER & FRESHWATER

• Chemical resistance of titanium is very good service (no effect-excellent) against sodium chloride (NaCl)-SALTWATER

• IC means integrated circuit

• Fully one year warranty

1. Place the heater tube unit in water in either vertical or horizontal position.  Press two suction cups firmly to glass to adhere heater unit to aquarium.  For best results, position the heater towards the bottom of the aquarium in a location that water circulates freely or use a power head (pump) to create the water circulation to ensure uniform heating temperature of water. 
2. Set the desired temperature by turning the temperature dial.  Wait five minutes until the heater tube is acclimatized to the aquarium water temperature.
3. If the temperature sensor unit separate from heater unit, adhere the temperature sensor unit by firmly pressing the suction cups to the aquarium.
4. Plug the power cord of the heater into the outlet.  The LCD display indicates whether the heater is ON/OFF (red light) and IN USE / NOT IN USE (green light).  If the RED light is displayed, the heating unit is ON.  If the RED light is not displayed, the heating unit has no source of electricity.  If the GREEN light is displayed, the heater is working to maintain set aquarium temperature.  If the GREEN light is NOT displayed, the heater has automatically shutoff after reaching set water temperature.  Controller unit provides a digital temperature LCD display that indicates the temperature of aquarium water.  Operating temperature range is between 68°F and 93°F.  The LCD display controller unit will maintain ± 1°F accuracy rating. 
5. After a few hours, check the water temperature with an accurate thermometer, if needed, adjust the temperature setting on the heating unit to achieve desired aquarium water temperature.

1. Fully submerse heater into water.  Never expose any portion of the heater to air.  The exposed portion of heater may burn out and malfunction

2. Never expose the thermo sensor to air. Exposure will produce inaccurate water temperature reading and cause heater to unnecessarily heat water according to the incorrect thermo sensor reading.

3. Never place the heater under gravel.  This will hinder even heat dissipation.

4. Never place the thermo sensor rear the heating tube.  It will cause inaccurate control of the water temperature.  Place the thermo sensor at least 12 inches (1 foot) away from the heating tube.

1. Do not operate the heater outside of water

2. To prevent possible electric shock, unplug heater before placing your hands in water

3. If an extension cord is necessary, a cord with proper rating  to avoid overheating

4. For proper operation, the heater tube should be positioned in a vertical or horizontal position in the water at all times.

5. Do not operated the heater if the cord or heating tube is damaged in any way.  The heater must be discarded.  Do not attempt to repair the unit. 

6. Unplug the heater during water change or when removing the unit from water for maintenance.  Wait at least 10 minutes for the heater to cool before removing from water.

7. Make sure that your electrical voltage is the same as the voltage listed on the label of the heater.

8. To avoid water contact to the heater plug or electric outlet, use a "drip loop" as shown below

SPECIAL NOTE

This aquarium heater has a one year limited warranty from the date of purchase, against defects in material or workmanship.  The limited warranty does not cover conditions caused by:
 

1. Damages caused by electrical spike, improper voltage and electrical surges.

2. Failure to follow the safety instruction.

3. Breakage and, or burning of the heating tube.

4. Cutting or altering the electrical cord.

5. Thermo sensor and, or electric cord that is chewed by fishes in the aquarium.

6. Changing of the IC circuit.

7. Re-adjusting of the temperature sensor in the IC circuit board.

8. The sealed epoxy is opened. 

This limited warranty is for the aquarium heater only.  This warranty does not cover livestock under any circumstances.  

LCD PRO-HEAT II IC HEATER  Sizes available

    APPROXIMATE HEATER GUIDE
The heater guide shows us approximate wattage depending on the size of tank and temperature difference between water of tank and room.  With this new chart it allows the consumer to achieve the desired temperature for that size tank.